Sentry Safe Fire-Safes Water Resistant

Programming your user code

To ADD a user code

1. Press the “Prog” key.
2. Enter the 5 digit factory code
3. The light will flash green and then you will have 30 seconds to enter your own personal user code. This code must be 5 digits.

To DELETE a user code

1. Press the “Prog”
2. Enter the 5 digit factory code.
3. Enter 0.0.0.0.0

NOTE: The electronic lock will NOT indicate that it has deleted the user code – please test the code to make sure it has been deleted.

NOTE: Delay mode will occur if three consecutive invalid entries have been tried. The red light will blink during delay mode. This will cause the system to shutdown for two minutes. Do NOT remove the batteries to restart the system – it will only increase the length of time for the system shutdown.

Programming your fingerprint (2 fingerprints allowed per person using the safe)

To ADD a user fingerprint:

1. Press the “PROG” key twice.
2. Enter the 5 digit factory code.
3. The blue light will blink when the system is waiting for a finger swipe. Swipe your finger in the downward direction over the fingertip sensor.

NOTE: If your finger swipe was accepted, a green light will flash and a beep will sound. If your finger swipe was not accepted, a red light will flash and a low beep tone will sound.

Five to ten accurate reads of the fingerprint are necessary for successful enrollment. Successful enrollment occurs when the green light flashes three times and three beeps are heard. Once this happens, you can swipe a second finger if you wish to enroll two fingerprints.

If enrollment is unsuccessful, the red light will flash three times and three low beep tones are heard. The system will then shut down and you should repeat steps 1-4.

To DELETE a user fingerprint:

1. Press the “PROG” key twice.
2. Enter the 5 digit factory code.
3. Press the “CLEAR” button.

NOTE: The biometric lock asks for two fingerprints when programming a user fingerprint. If you would like to only use one, allow for lock to timeout or press the “CLEAR” button.

NOTE: You are allowed 10 errors when enrolling a fingerprint – if you cannot enroll a finger in that time, the system will flash a red light three times, beep three times, and shut down. Try enrolling again by repeating steps 1-4.

Unlocking your safe using a fingerprint

Key lock must be in the unlocked position, signified by the lock cylinder being popped out.

1. Press the “CLEAR” button to first awaken your safe.
2. Swipe your finger in a downward direction over the fingerprint sensor. A green light and one beep indicate the acceptance of a fingerprint.
3. Rotate the handle downward to open the door.

Programming a secondary code and fingerprint (2 fingerprints allowed per person using the safe)

To ADD a secondary code and fingerprint:

1. Press the “PROG” key.
2. Enter the 5 digit user code.
3. Enter the new 5 digit secondary code
4. The blue light will blink when the system is waiting for a finger swipe. Swipe your finger in the downward direction over the fingertip sensor.

NOTE: If your finger swipe was accepted, a green light will flash and a beep will sound. If your finger swipe was not accepted, a red light will flash and a low beep tone will sound.

Five to ten accurate reads of the fingerprint are necessary for successful enrollment. Successful enrollment occurs when the green light flashes three times and three beeps are heard.

If enrollment is unsuccessful, the red light will flash three times and three low beep tones are heard. The system will then shut down and you should repeat steps 1-5.

If you would not like to enroll a finger, wait for the system to timeout or press the “CLEAR” button.

To DELETE a secondary code and fingerprint:

1. Press the “PROG” key.
2. Enter the 5 digit user code.
3. Press 0,0,0,0,0.

NOTE: Deleting a secondary fingerprint will also delete the secondary code.

NOTE: The biometric lock asks for two fingerprints when programming a user fingerprint. If you would like to only use one, allow for lock to timeout or press the “CLEAR” button.

Erasing all codes and fingerprints

NOTE: You will never be able to delete the factory code.

To DELETE all codes and fingerprints:

1. Press 0.
2. Press the “PROG” key.
3. Press 9.
4. Enter the 5 digit factory code.

Turning the sound off/on

To turn the sound OFF:

1. Press 0.
2. Press the”PROG” key.
3. Press 2.

To turn the sound ON:

1. Press 0.
2. Press the”PROG” key
3. Press 1.